Perun ETU++ Perun ETU++ Electronic Board for G&G Perun ETU++
SKU: 1654
Perun

Perun ETU++ Electronic Board for G&G

£48.00

The ETU++ is a dedicated replacement for G&G ETU electronic board. It enhances your trigger unit by adding many new, useful features. Simply disconnect the stock electronic board and plug in the ETU++. The stock trigger unit (switch set) is retained, so there is no need to open the gearbox.

Works with any G&G ETU replica on 7.4V, 11.1V and 14.8V batteries.

Features:

  • Independently programmable firing modes
  • Active brake with adjustable braking power
  • Precocking (with spring release feature)
  • Binary trigger
  • Rate of fire reduction
  • DMR mode
  • Low battery voltage alarm
  • Programming supported with a multicolor LED diode
  • Diagnostic system
  • Electronic resettable fuse


Independently programmed firing modes - Program the firing modes any way you like, setting safe, semi, burst or auto on both selector positions.

Active brake - active brake stops the motor after each shot preventing spring compression or in case of replicas with high rate of fire, overspin and double shooting.

Precocking – A fast trigger response can make the difference between victory and defeat, especially in CQB situations. With precocking enabled, the piston will remain in the rear position after each shot with the spring already compressed, ensuring that next shot will be fired immediately after you pull the trigger. To release the spring after using precocking, pull the trigger while simultaneously holding the button on the unit. A shot will be fired, fully braked with no precocking.

Binary trigger - Allows for easy double shots in semi-automatic setting. After enabling this mode, if semi-automatic fire is set, shots will be fired not only when the trigger is pulled, but also when it is released.

Rate of fire reduction - Reduce the rate of fire in automatic or burst fire to save ammo or make the replica shoot in a more realistic fashion.

DMR mode - Introduces intervals between semiautomatic shots to comply with DMR rules on some fields.

Low battery voltage alarm - Dedicated for Li-Po and Li-Ion batteries. Should the battery voltage fall to a dangerously low level, user will be notified by short sound signals that are repeated every minute. This may also be freely switched on and off.

Diagnostic system - Constantly monitors the replica and the mosfet itself. In case of any problems, immediately lets you know what it might be, making troubleshooting much easier.

Full Description
Qty
  • Description

    The ETU++ is a dedicated replacement for G&G ETU electronic board. It enhances your trigger unit by adding many new, useful features. Simply disconnect the stock electronic board and plug in the ETU++. The stock trigger unit (switch set) is retained, so there is no need to open the gearbox.

    Works with any G&G ETU replica on 7.4V, 11.1V and 14.8V batteries.

    Features:

    • Independently programmable firing modes
    • Active brake with adjustable braking power
    • Precocking (with spring release feature)
    • Binary trigger
    • Rate of fire reduction
    • DMR mode
    • Low battery voltage alarm
    • Programming supported with a multicolor LED diode
    • Diagnostic system
    • Electronic resettable fuse


    Independently programmed firing modes - Program the firing modes any way you like, setting safe, semi, burst or auto on both selector positions.

    Active brake - active brake stops the motor after each shot preventing spring compression or in case of replicas with high rate of fire, overspin and double shooting.

    Precocking – A fast trigger response can make the difference between victory and defeat, especially in CQB situations. With precocking enabled, the piston will remain in the rear position after each shot with the spring already compressed, ensuring that next shot will be fired immediately after you pull the trigger. To release the spring after using precocking, pull the trigger while simultaneously holding the button on the unit. A shot will be fired, fully braked with no precocking.

    Binary trigger - Allows for easy double shots in semi-automatic setting. After enabling this mode, if semi-automatic fire is set, shots will be fired not only when the trigger is pulled, but also when it is released.

    Rate of fire reduction - Reduce the rate of fire in automatic or burst fire to save ammo or make the replica shoot in a more realistic fashion.

    DMR mode - Introduces intervals between semiautomatic shots to comply with DMR rules on some fields.

    Low battery voltage alarm - Dedicated for Li-Po and Li-Ion batteries. Should the battery voltage fall to a dangerously low level, user will be notified by short sound signals that are repeated every minute. This may also be freely switched on and off.

    Diagnostic system - Constantly monitors the replica and the mosfet itself. In case of any problems, immediately lets you know what it might be, making troubleshooting much easier.

  • Reviews

    Reviews

    Be the first to

  • Details

    Details

    Current Stock:
    SKU: 1654
    UPC: 5907622628139
    Width: 10.000 (cm)
    Height: 8.000 (cm)
    Depth: 1.500 (cm)